The same drawing sent to three die casters can come back with quotes that differ by a factor of two. Most of the time nobody is trying to overcharge you — the quotes simply contain different things. One includes tooling, one excludes finishing, one has scrap built into the unit price and another does not.
This guide breaks die casting cost into six components, then covers five levers that actually reduce it, and four moves that look like savings but are not.
| Component | How it is calculated | What drives it |
|---|---|---|
| Tooling amortisation | One-off investment spread over order volume | Cavities, die material, required life, slides |
| Material | Unit price × part weight × (1 + scrap rate) | Alloy, runner and overflow ratio, regrind allowance |
| Casting time | Shots × cycle time × machine rate | Wall thickness, tonnage, automation, cooling time |
| Secondary operations | Added per operation | Deburring, CNC machining, tapping, drilling, straightening |
| Surface finishing | Per part or per area | Painting, plating, anodising, passivation, blasting |
| Scrap rate | Hidden, usually in the unit price | Part complexity, tolerance tightness, tool condition |
Once you see this table, it is obvious why two quotes are often not comparable: if any one component is defined differently, the totals mean nothing. The first question is not “how much”, it is “what is included”.
Buyers often divide tooling cost by annual volume to get a unit cost. That works at high volume and badly misleads at low volume:
At around 1,000 parts a year, tooling can be more than half of the unit price
At 100,000 parts a year, tooling becomes almost irrelevant next to material and cycle time
The same part made on a die built for five years versus two years costs differently
Wall thickness drives part weight, cooling time and material consumption, so it is the most sensitive cost parameter. But it has limits: fill, sink marks and strength must still hold. Thin it without analysis and scrap goes up, which costs more than it saves.
CNC is charged by surface and by hour. Drawings often mark every face as machined when only assembly faces, sealing faces and bearing seats need it. Leaving non-critical faces as-cast removes a meaningful share of machining cost.
Take a thin-wall part like this actuator housing: every surface you stop machining also removes one clamping setup and the distortion risk that comes with it.
Every step tighter in tolerance costs yield and cycle time. Grade your tolerances: tight on functional interfaces, loose on cosmetic and non-mating surfaces. This is usually the highest-return change available. For how to grade them, see our die casting tolerances guide.
One casting replacing three or four stampings plus assembly removes multiple tools, assembly labour, and inventory complexity. Design effort is higher up front, but production cost diverges quickly.
We have done this kind of consolidation on both electronics castings and automotive castings — merging separate brackets and fasteners into one body is usually the most direct way to cut unit cost.
Yield is the most overlooked component. At the same quoted price, lifting yield from a mediocre level to a good one cuts real delivered cost substantially. Yield comes from three things: DFM and flow simulation before tooling, a sensible die maintenance cycle, and stable process parameters.
| Move | Looks like | Actually costs |
|---|---|---|
| Tolerances too tight | Assured quality | Whole batch goes to CNC; price up, lead time up |
| Skipping DFM and flow simulation | A fee avoided | More trial shots; die corrections cost far more |
| Squeezing the toolmaker | One-off saving | Short die life, frequent repairs, dimensional drift |
| Comparing material price only | Cheaper on paper | Density and downstream operations ignored |
Half of all quote variance comes from incomplete requirements. Send these in one go and you will get a number closer to real cost, with less back-and-forth later:
3D model (STEP or IGES), not just images
2D drawing with critical dimensions and tolerances, plus the general tolerance standard
Alloy, or the service conditions if you want a recommendation
Finishing requirements, including colour, film thickness and salt-spray hours
Annual volume and batch pattern — this determines how tooling is amortised
Acceptance criteria: leak test, Cpk, full dimensional report, material certificates
Break each quote into the same six components instead of comparing totals. What usually emerges: the higher total has lower tooling and machining cost and simply accounts for material and finishing honestly; the lower total is missing inspection or scrap.
The goal is not the lowest number — it is the supplier whose cost structure is sound and has no hidden items.
Cost structure varies a lot by product line: automotive parts carry inspection and traceability cost, industrial parts are machining-heavy, and energy parts cannot skip leak testing. It helps to look at automotive castings, industrial castings and energy management castings before deciding where your part sits.
We provide DFM review, flow simulation and itemised cost estimates before tooling is cut, showing tooling, material, machining and finishing separately. Send a drawing and we will return a breakdown you can compare side by side.